Read the main scale
Look at where the vernier zero ended up (the yellow line). The whole millimeters it has passed are the first part: if the zero is between 23 and 24, that's 23 mm.
Learn to read a vernier caliper by moving the slider or practicing with random measurements. Works with 0.1, 0.05 and 0.02 mm verniers and in inches (0.001"). It explains each reading step by step and highlights the matching line.
Magnifier
Drag the caliper slide, or the scale in the magnifier.
How to read this measurement
Step by step
Look at where the vernier zero ended up (the yellow line). The whole millimeters it has passed are the first part: if the zero is between 23 and 24, that's 23 mm.
Scan along the vernier until you find the line that sits exactly in line with a line on the main scale. There's only one. Its number, multiplied by the resolution (0.05 or 0.02 mm), gives the tenths and hundredths.
Main scale + vernier. With 23 mm on the main scale and line 7 on a 0.05 vernier: 23 + 7 × 0.05 = 23.35 mm. The vernier numbers already give you the tenths: the line marked “3” is 0.30 and the next one, 0.35.
Before measuring
If you don't look square to the scale, the line that seems to line up isn't the right one (parallax error). Put your eye right above the line.
A caliper has no ratchet: if you squeeze, the jaws spread a little and soft parts deform. Close it gently, with the part as far into the jaws as possible.
Before measuring, close the clean caliper: the vernier zero has to line up with the main scale zero. If it doesn't, there's dirt or the caliper has taken a knock.
The farther from the scale you measure, the more any play in the slider shows (Abbe principle). Measure with the part of the jaws closest to the scale.
Questions
Read the whole millimeters on the main scale, to the left of the vernier zero. Then find the vernier line that lines up with one on the main scale: each line is worth 0.05 mm. Add the two readings. Example: 12 mm + line 9 × 0.05 = 12.45 mm.
The 0.05 one has 20 divisions over 39 mm; the 0.02 one, 50 divisions over 49 mm. The 0.02 one resolves finer, but it has more lines and it's harder to see which one lines up. In real shop practice, a caliper's actual resolution is around 2–3 hundredths even if the vernier says 0.02.
Both work the same way (each division is 0.05 mm shorter than 2 mm or 1 mm), but the 39 mm one spaces the lines further apart and is easier to read. It's the most common on current calipers.
According to ISO 13385-1, the maximum permissible error of a 150 mm caliper with a 0.02 vernier is around ±0.02–0.03 mm. For tolerances in hundredths, use a micrometer.
Internal measurements use the small upper jaws, which open outward; depth uses the rod that comes out the back. Reading works the same as for external measurements.
Where the data comes from
The data on this page comes from these standards and catalogs. If you see a figure that doesn't match your catalog, write to us and we'll check it.
Learn to read an outside micrometer in 0.01 mm, 0.001 mm with vernier or in inches: turn the thimble, check the sleeve and the half millimeter, and practice with 10 random measurements.
Learn to read a 0.01 mm, 0.002 mm or 0.001" dial indicator: large pointer and revolution counter, with each reading explained, exercises and the typical mistakes when centering and measuring.
Calculates indicative ISO 286 tolerances for shaft and hole, H7/g6, H7/h6, H7/k6 and H7/p6 fits with clearance, transition and interference graph.
We use technical and security cookies and, only if you accept, analytics with no cross-site tracking. More in the Cookie policy and Privacy policy.
We use first-party cookies and technical storage to make the site work, Google reCAPTCHA security technology and, only if you accept, Vercel analytics (no cookies, no cross-site tracking). You can accept or reject analytics; both options are equivalent and you can change your choice at any time. More info: Cookie policy, Privacy policy, Legal notice and Terms and conditions.