Millimeters on the sleeve
The lines above the reference line are whole millimeters. Count the last one visible before the edge of the thimble.
Learn to read an outside micrometer by turning the thimble or practicing with random measurements. 0.01 mm micrometers (0–25 and 25–50), 0.001 mm with vernier and inch (0.001"). It explains the sleeve, the half millimeter and the thimble on every reading.
Magnifier
Drag the thimble; in the magnifier, up and down to turn it.
How to read this measurement
Step by step
The lines above the reference line are whole millimeters. Count the last one visible before the edge of the thimble.
The lower lines are the half millimeters. If a lower line is already showing after the last millimeter, add 0.5 mm. It's the most common mistake when reading a micrometer.
The thimble has 50 divisions of 0.01 mm (one turn = 0.5 mm). Read the division that sits on the reference line and add it: 12 + 0.5 + 0.27 = 12.77 mm. On 0.001 models, the vernier on the sleeve gives the thousandth.
Before measuring
If you read 12.27 when it's 12.77, you've forgotten the lower line. Always check whether a half-millimeter line shows between the last millimeter and the thimble.
Always tighten with the ratchet or friction stop, two or three clicks. With the thimble you can overtighten and read several hundredths too small.
Close the clean micrometer (or onto the setting standard on 25–50 ones): the thimble's 0 has to sit on the line. If not, adjust the sleeve with the wrench.
A 50 mm steel part grows about 6 µm for every 10 °C. Let the part cool down or measure at the same temperature as the micrometer.
Questions
Add three things: the whole millimeters on the sleeve (upper lines), 0.5 mm if a lower line shows after the last millimeter, and the thimble division sitting on the reference line (each one is 0.01 mm).
Because the spindle advances 0.5 mm per turn. 0.5 mm divided by 50 divisions gives 0.01 mm per division. In inches the pitch is 0.025" and the thimble has 25 divisions of 0.001".
First read to the hundredth as on a standard one. Then find the vernier line on the sleeve (numbered 0 to 10) that lines up with a thimble line: that number is the thousandths.
According to ISO 3611, a 0–25 mm micrometer has a maximum permissible error of around ±2 µm. It's ten times better than a caliper, which is why it's used for tolerances in hundredths.
So you always measure with the same force. The ratchet slips when the spindle touches the part with just the right force; that way two people measure the same.
Where the data comes from
The data on this page comes from these standards and catalogs. If you see a figure that doesn't match your catalog, write to us and we'll check it.
Learn to read a vernier caliper with 0.1, 0.05 and 0.02 mm verniers or in inches: move the slider, find the matching line and practice with 10 random measurements. Free, in your browser.
Learn to read a 0.01 mm, 0.002 mm or 0.001" dial indicator: large pointer and revolution counter, with each reading explained, exercises and the typical mistakes when centering and measuring.
Calculates indicative ISO 286 tolerances for shaft and hole, H7/g6, H7/h6, H7/k6 and H7/p6 fits with clearance, transition and interference graph.
We use technical and security cookies and, only if you accept, analytics with no cross-site tracking. More in the Cookie policy and Privacy policy.
We use first-party cookies and technical storage to make the site work, Google reCAPTCHA security technology and, only if you accept, Vercel analytics (no cookies, no cross-site tracking). You can accept or reject analytics; both options are equivalent and you can change your choice at any time. More info: Cookie policy, Privacy policy, Legal notice and Terms and conditions.