What each letter and number in a turning insert code means according to ISO 1832: shape, clearance angle, tolerance, hole and chipbreaker, size, thickness and nose radius. With a scale drawing, inch equivalent and compatible toolholder.
Examples
PM—
Equivalent
Top view and side view to the same scale. Hover over a position to see it on the drawing.
What each position means
Click a box in the code or a dropdown to build another code
1
Form
Rhombic 80°
The most used for longitudinal turning and facing: strong corner for roughing and semi-finishing, with two usable corners per side.
2
Clearance angle
0° (negative)
Negative: the toolholder tilts it so it doesn't rub. It takes chipbreakers on both sides (twice the edges) and is tougher.
3
Tolerance
Class M
m ±0.08 to ±0.2 · s ±0.13 · d ±0.05 to ±0.15 mm. Sintered, periphery not ground: the most common in turning (CNMG, DNMG, VBMT).
4
Hole and chipbreaker
Cylindrical hole, chipbreaker on both faces
5
Size
12.9 mm edge · inscribed circle Ø 12.7 mm
6
Thickness
4.76 mm
7
Nose radius
r = 0.8 mm
8
Edge preparation
Not specified (it's optional)
9
Cutting direction
Not specified (it's optional)
+PM
Manufacturer
chipbreaker PM
Not ISO: each brand puts its chipbreaker and grade here. Check its catalog.
In the ISO 5608 toolholder code, the 2nd letter is the shape and the 4th the clearance. The 1st is the clamping: for a cylindrical hole, lever (P), clamp and pin (M) or rigid clamp (D); for a countersunk hole, screw (S); without a hole, top clamp (C). The last one, R or L, is the hand.
Surface finish from this radius
Ra ≈ 1.56 µm
Theoretical roughness Ra ≈ f² / (32·r). The real one comes out a bit worse due to vibration and wear. For roughing, shop rule: feed up to half the radius. Calculate speed and feed
Sizes
Sizes for this shape C (Rhombic 80°)
The bigger the insert, the bigger the drawing. The ones marked as common are in any catalog; the rest exist, but few brands make them. To change the size, use box 5 of the code.
04cutting edge 4.8 mmØ 4.76 mmUncommon
05cutting edge 5.6 mmØ 5.56 mmUncommon
06cutting edge 6.4 mmØ 6.35 mmCommon
08cutting edge 8.1 mmØ 7.94 mmUncommon
09cutting edge 9.7 mmØ 9.525 mmCommon
12cutting edge 12.9 mmØ 12.7 mmYour code
16cutting edge 16.1 mmØ 15.875 mmCommon
19cutting edge 19.3 mmØ 19.05 mmCommon
25cutting edge 25.8 mmØ 25.4 mmCommon
32cutting edge 32.2 mmØ 31.75 mmUncommon
Cards
Most searched codes
Each code has its own page with what it means, its dimensions and its drawing.
The ISO 1832 code describes the insert position by position: first four letters that tell its shape and how it's clamped, then three numbers with its dimensions and, if needed, two optional letters. Knowing it helps you order the right insert, find the equivalent from another brand and choose the toolholder.
11
The four letters
Shape (C, D, V, T, W, S, R…), clearance (N negative, C 7°, B 5°, P 11°…), tolerance (M the most common, G ground) and hole and chipbreaker type (G, M, T, W…). With these letters you already know which toolholder it fits: the shape and the clearance repeat in the toolholder code.
22
The three numbers
Size (cutting edge length in mm), thickness and nose radius in tenths of a millimeter: 120408 is a 12 edge, thickness 04 (4.76 mm) and radius 0.8. In inch codes the numbers mean something different (CNMG 432) but the letters don't.
33
What the manufacturer adds
After the dash come the chipbreaker and the grade: CNMG 120408-PM 4325. It isn't ISO, so two brands can use the same letters for different things. To replace an insert from another brand, match the ISO code and choose the chipbreaker by material and type of cut.
Questions
Frequently asked questions
What does CNMG 120408 mean?
C = 80° rhombic, N = 0° clearance (negative), M = tolerance M (sintered), G = cylindrical hole and chipbreaker on both faces. 12 = 12 mm cutting edge (12.7 mm inscribed circle), 04 = 4.76 mm thickness and 08 = 0.8 mm nose radius. What comes after the dash (PM, MF, MA…) is each manufacturer's chipbreaker.
What's the difference between a negative and a positive insert?
A negative insert (second letter N) has straight flanks and the toolholder tilts it so it doesn't rub: it's stronger and can have chipbreakers on both sides, with twice the edges. A positive one (B, C, P…) has angled flanks: it cuts with less force and vibrates less, so it's used on thin parts, small machines and boring, but it only works on one side.
How do you convert CNMG 432 to metric?
In inches, the first number is the inscribed circle in eighths of an inch (4 = 1/2" = 12.7 mm), the second the thickness in sixteenths (3 = 3/16" = 4.76 mm) and the third the radius in sixty-fourths (2 = 1/32" = 0.8 mm). So CNMG 432 = CNMG 120408. The letters are the same in both systems.
Why are a CNMG 09 and a TNMG 16 the same size?
Because the size number is the cutting edge length, not the inscribed circle. With the same 9.525 mm inscribed circle, the triangular one has a 16.5 mm side (TNMG 16), the 80° rhombic one 9.7 mm (CNMG 09) and the 35° one 16.6 mm (VBMT 16). To compare inserts of different shapes, look at the inscribed circle.
Which nose radius should I choose?
A bigger radius gives a stronger edge and a better finish at the same feed, but it pushes the part harder and chatters sooner. Shop rule: when roughing, don't go above a feed of half the radius (r 0.8 → up to 0.4 mm/rev); when finishing, feed sets the roughness: Ra ≈ f² / (32·r). On thin or long parts, small radius (0.2–0.4).
What does the “T” in the thickness mean in 09T304?
That it's an intermediate thickness between that number and the next: T3 = 3.97 mm (5/32"), between 03 (3.18 mm) and 04 (4.76 mm). The same goes for T1 (1.98 mm) and T2 (2.78 mm).
Are the letters at the end (PM, MF, MA, -WF) ISO?
No. The standard ends at position 9 (cutting direction). What comes after is up to each manufacturer: the chipbreaker and the carbide grade. At Sandvik the first letter is usually the material group (P, M, K…) and the second the type of cut (F finishing, M medium, R roughing); other brands use their own names. Always check their catalog.
What does 16ER 1.5 ISO mean on a threading insert?
It's a laydown threading insert: 16 is the size (16.5 mm side, 3/8" inscribed circle), E external (I would be internal), R right-hand, 1.5 the pitch in mm and ISO the full 60° metric profile. If it says AG60 instead of a pitch, it's a 60° partial profile that works for pitches from 0.5 to 3 mm. It isn't an ISO 1832 code, but almost every brand uses the same one.
Where the data comes from
Sources (4)
The data on this page comes from these standards and catalogs. If you see a figure that doesn't match your catalog, write to us and we'll check it.
standard[1]ISO 1832:2017 — Indexable inserts for cutting tools — DesignationISO
standard[2]ANSI B212.4 — Indexable inserts, inch designationANSI
catalog[3]General turning catalog: ISO code key for inserts and toolholdersSandvik Coromant
book[4]Machinery's Handbook, 31st ed., chapter on indexable insert toolsIndustrial Press
We use technical and security cookies and, only if you accept, analytics with no cross-site tracking. More in the Cookie policy and Privacy policy.
We use first-party cookies and technical storage to make the site work, Google reCAPTCHA security technology and, only if you accept, Vercel analytics (no cookies, no cross-site tracking). You can accept or reject analytics; both options are equivalent and you can change your choice at any time. More info: Cookie policy, Privacy policy, Legal notice and Terms and conditions.