The five letters
Clamping (P lever, S screw, C clamp, M clamp and pin, D rigid clamp), insert shape (C, D, V, T, W, S, R…), style and lead angle (L 95°, J 93°, N 63°, S 45°…), insert clearance angle (N negative, C 7°, B 5°…) and hand (R, L or N).
What each letter and number in the code of a lathe toolholder (ISO 5608) or a boring bar (ISO 6261) means: clamping, insert shape and clearance angle, lead angle, hand, shank and length.
Clamping
Lever in the hole
Insert with cylindrical hole (M, G, A)
Insert shape
Rhombic 80°
The most used for longitudinal turning and facing: strong corner for roughing and semi-finishing, with two usable corners per side.
Style and lead angle
κr 95° · offset
Turning and facing with the same corner: the most used with C and W inserts
Insert clearance angle
0° (negative)
For negative inserts (CNMG, DNMG, WNMG…).
Hand
Right-hand
Cuts toward the chuck on a conventional lathe (right to left).
Shank height
25 mm
It has to match the turret's center height (or be shimmed up to it).
Shank width
25 mm
Length
150 mm
Insert size
12.9 mm edge · inscribed circle Ø 12.7 mm
Cards
Each code has its own page with what it means, its dimensions and its drawing.
Guide
The ISO 5608 code for an external turning toolholder has five letters, three dimensions and the insert size. Boring bars (ISO 6261) start with the type and the bar diameter and then follow the same pattern. Knowing it helps you order the right toolholder and know which insert it takes without opening the catalog.
Clamping (P lever, S screw, C clamp, M clamp and pin, D rigid clamp), insert shape (C, D, V, T, W, S, R…), style and lead angle (L 95°, J 93°, N 63°, S 45°…), insert clearance angle (N negative, C 7°, B 5°…) and hand (R, L or N).
Shank height and width in mm (2525, 2020, 3225) and a letter for the length: H 100, K 125, M 150, P 170, Q 180, R 200, S 250. The height has to put the tip at the workpiece center height on your turret.
The last number is the insert size, same as in its code: 12 in a PCLNR is a CNMG 12. Manufacturer letters may follow, such as through-shank coolant or a quick-change system.
Questions
P = lever clamping, C = 80° rhombic insert, L = 95° lead angle, N = negative insert (0°), R = right-hand, 25 × 25 = shank 25 mm high and 25 mm wide, M = 150 mm long and 12 = size 12 insert (CNMG 12…).
The 2nd letter is the insert shape, the 4th its clearance and the last number its size. A PCLNR …12 takes a C·N·· 12, for example CNMG 120408 or CNMM 120412. The 1st letter tells you whether it needs a cylindrical hole (P, M, D), a countersunk hole (S) or no hole (C).
It's the angle between the main cutting edge and the feed direction. At 90–95° the thrust goes toward the Z axis and the part deflects less: it's the one used for long parts and for facing with the same corner. At 45–75° the chip comes out thinner for the same feed and the edge holds up better in roughing, but it pushes the part outward more.
It's the hand. R cuts from right to left (toward the chuck on a standard lathe) and L from left to right. Depending on where the turret is and which way the spindle turns, your machine may need the opposite hand; if in doubt, check which side of the centerline the insert sits on with the tool mounted.
It starts with the bar type (S steel, A steel with coolant, C carbide, E carbide with coolant), its diameter in mm and a length letter. After the dash comes the same as on an external toolholder: clamping, shape, angle, clearance, hand and size. So A25T-PCLNR12 is a steel bar with coolant, Ø 25 and 300 mm long, taking a CNMG 12 at 95°.
As a catalog guideline: a steel bar up to about 4 times its diameter, a carbide one up to about 6 and an anti-vibration bar quite a bit more. Beyond that it chatters. Use the thickest bar that fits in the hole and keep the overhang as short as possible.
The external one has a square shank (2525, 2020…) and works on the outside of the part. The internal boring bar is round, goes into the hole and its code starts with the type and the diameter (S20S, A25T…). What limits the bar is overhang: steel, up to about 4 times its diameter; carbide, up to about 6. And the hole has to be somewhat larger than the bar so the insert and the chips fit.
They're threading toolholders for laydown inserts. S is the series, E external or I internal, R right-hand. For external tools, 2525 is the 25 × 25 shank; for internal ones, 0020 is a Ø 20 bar. The letter is the length (M 150, Q 180) and the last number is the insert size: 16 takes 16ER or 16IR inserts.
Where the data comes from
The data on this page comes from these standards and catalogs. If you see a figure that doesn't match your catalog, write to us and we'll check it.
Type in the code of a lathe insert (CNMG 120408, DCMT 11T304, VBMT 160404…) and it explains every letter and number according to ISO 1832, with a scale drawing, the inch equivalent (CNMG 432) and the toolholder that fits it.
Cutting speed (Vc), rpm, feed and theoretical surface finish for turning, milling, drilling and threading by material and tool. A starting point.
Real two-channel cycle time by critical path (M100, P, WAITM and !L waits), transfer review, main→sub pick-off routine with your own codes, parting/length setup and Z1/Z2.
We use technical and security cookies and, only if you accept, analytics with no cross-site tracking. More in the Cookie policy and Privacy policy.
We use first-party cookies and technical storage to make the site work, Google reCAPTCHA security technology and, only if you accept, Vercel analytics (no cookies, no cross-site tracking). You can accept or reject analytics; both options are equivalent and you can change your choice at any time. More info: Cookie policy, Privacy policy, Legal notice and Terms and conditions.